The Linksys WRVS4400N does not support direct VPN connections using a PPTP or L2TP VPN client. The Linksys RV042/81 does, but I think they are the only Linksys with that capability. Using that client it would have to be a pass-through, but should be fine for that type of connection.
Here are the steps I went through to setup a VPN connection to my WRVS4400N VPN router. I built a VPN user under the VPN | VPN Client Account and saved the account. Next I generated both the Admin and Client Certificates and downloaded both to my local computer. Next I enabled Firewall / Basic Settings / Remote Management. Hi - I have 2 WRVS4400N's installed in our network, one at each end of a VPN tunnel between 2 physical locations. I continue to have issues with the VPN to "Stay" connected, even after purchasing another new WRVS4400N 4 months ago. I can reboot both routers, and the VPN connects with no problem, I recently purchased a pair of WRVS4400N's for the sole purpose of establishing a vpn between two sites. I have followed the vpn directions given in previous messages on this board with no success. The routers both are connected to Time Warner cable modems with static ip's, both have the vpn section completed properly, using subnet security & each other's wan ip's for remote gateway security. Here are the steps I went through to setup a VPN connection to my WRVS4400N VPN router. I built a VPN user under the VPN | VPN Client Account and saved the account. Next I generated both the Admin and Client Certificates and downloaded both to my local computer. Next I enabled Firewall / Basic Settings / Remote Management.
Cisco WRVS4400N Small Business / Home Router with L7 IPS and NAT (both hardware accelerated), a VLAN capable switch, pci wlan card (b/g/n). Supported Versions
The WRVS4400N has advanced security including an optional security service helps block malicious websites and control web access. Offsite workers can access your network through a secure and easy-to-use virtual private network (VPN) connection. IPSec VPN can be locally or remotely grouped. The local group determines who in the network can access the tunnel while remote group determines who from the remote network can connect to the network through the tunnel on the WRVS440N router. This article explains how to configure the IPSec VPN Local and Remote Group Setup on WRVS4400N router.
View and Download Linksys WRVS4400N user manual online. Wireless-N Gigabit Security Router with VPN Business Series. WRVS4400N Wireless Router pdf manual download.
WRVS4400N. • Fixed an issue in the VPN code that caused the QuickVPN client to drop the connection when the QuickVPN client connects to the QuickVPN server behind a NAT router. Known Issues Oct 17, 2011 · The WRVS4400N WAN port picked up an IP on our LAN from the DHCP server on the AG300. I set the WAN port MTU configuration to Manual (Setup, WAN) and MTU size to 1000. This on the basis that the VPN traffic will be tunnelled so the MTU better be less than 1500. 1000 is no doubt lower than necessary but I didn't want failure for the sake of a few WRVS4400N. • Fixed an issue in the VPN code that caused the QuickVPN client to drop the connection when the QuickVPN client connects to the QuickVPN server behind a NAT router. Known Issues Specifications This appendix lists the specifications of the Cisco WRVS4400N Wireless-N Gigabit Security Router with VPN. General WRVS4400N Model Standards Draft IEEE802. 1 1n, IEEE802. 1 1g, IEEE802. 1 1b, IEEE802.3, IEEE802.3u, 802. 1 X (Security Authentication), IEEE802. 1 Q (VLAN), 802. Buy Cisco Small Business WRVS4400N Wireless-N Gigabit Security Router IEEE 802.11b/g/n, IEEE 802.3/3u/3ab with fast shipping and top-rated customer service.